Your donations help keep this valuable resource free and growing. Thank you.
|
ignition key/cylinder, etc |
Post Reply | Page 12> |
Author | |
billd
Moderator Group Forum Administrator Joined: Jun/27/2007 Location: Iowa Status: Offline Points: 30894 |
Post Options
Thanks(0)
Posted: Nov/18/2007 at 11:26pm |
The ignition switch (ok, not reall the switch) lock cylinder can be operated with no key. The key can be pulled even before the lock is all the way back (lever on colum to release)
Is this best repaired, or simply replaced?
Can it be fixed and rekeyed, or should I look for another?
I don't like the fact that someone can simply get in it and start it with no key, although today, they'd be screwed, the tranny is jammed again.
If it's best to just replace it, I guess I'll be placing a wanted ad...........
Also, what is the removal procedure? Is it the same on all years?
|
|
tufcj
Supporter of TheAMCForum Supporter of TheAMCForum Joined: Jul/10/2007 Location: Watkins, CO Status: Offline Points: 4086 |
Post Options
Thanks(0)
|
It's worn out, probably best to just replace it. My Jeep does the same thing, so I installed a hidden ignition cut-out switch.
The procedure is nearly the same for all Saginaw columns. 1. remove steering wheel and lock plate you need a compressor tool to remove the lock plate. you may need to loosen and lift the directional assembly to see under it. 2. with the key in the "on" position, you push a tab at the back end of the lock barrel, it will slide out. Bob tufcj |
|
69 AMX
74 Javelin AMX 67 Rogue If you need a tool and don't buy it... you'll eventually pay for it... and not have it. Henry Ford |
|
billd
Moderator Group Forum Administrator Joined: Jun/27/2007 Location: Iowa Status: Offline Points: 30894 |
Post Options
Thanks(0)
|
If I get a replacement, I assume it can be "re-keyed" for to match the door locks?
I'd like to keep the "one key, all locks" setup these cars use. I've got NOS key blanks for this I'd like to use or maybe get a good setup and keep two individual keys, no problem there, really.
|
|
tufcj
Supporter of TheAMCForum Supporter of TheAMCForum Joined: Jul/10/2007 Location: Watkins, CO Status: Offline Points: 4086 |
Post Options
Thanks(0)
|
They can be re-keyed, you may have to find a willing GM dealership to do it. I don't know how many locksmiths re-key car locks.
Bob tufcj |
|
69 AMX
74 Javelin AMX 67 Rogue If you need a tool and don't buy it... you'll eventually pay for it... and not have it. Henry Ford |
|
IowaEagle
Supporter of TheAMCForum Charter Member Joined: Jun/30/2007 Location: Iowa Status: Offline Points: 633 |
Post Options
Thanks(0)
|
We have a guy here in Marshalltown who will be glad to re-key. Not a dealership, just a master locksmith.
|
|
kirkwood
Moderator Group Charter Member Joined: Jun/28/2007 Location: Fort Wayne, IN Status: Offline Points: 6566 |
Post Options
Thanks(0)
|
not quite re-key as you think. The napa/o'reilly's etc lock cylinders work fine, but use a GM key. They can cut that key to work with your existing door locks, but don't expect to cut an AMC key and have it work in the new cylinder - the key blanks are different.
|
|
AMO Newsletter Editor
|
|
billd
Moderator Group Forum Administrator Joined: Jun/27/2007 Location: Iowa Status: Offline Points: 30894 |
Post Options
Thanks(0)
|
I'd much rather get a good used AMC lock cylinder. I don't want to get into mixed keys, etc.
So I may have to hold out until I find someone parting a later AMC and buy the lock parts. All I should need is the ignition lock cylinder and can have that changed. Or I guess be forced to use one key for the ign and another for the doors. The hatch is electric.
|
|
CloudyB
Supporter of TheAMCForum Joined: Jul/05/2007 Location: United States Status: Offline Points: 2369 |
Post Options
Thanks(0)
|
Hey Billd. You might find what your looking for here
|
|
billd
Moderator Group Forum Administrator Joined: Jun/27/2007 Location: Iowa Status: Offline Points: 30894 |
Post Options
Thanks(0)
|
I've got to ask him a question as the image makes it look like it states "will fit GM, AMC which means it's probably a GM lock. That's what I want to avoid.
I want a genuine AMC, even if used.............
I'll write him and clarify.
Confirmed - the same thing I'd buy locally, GM locks taking a GM style key.
Thanks, but I'll look for an AMC lock cylinder. Gotta be someone scrapping an Eagle or Spirit....... Edited by billd - Nov/19/2007 at 1:51pm |
|
XJ-001
Supporter of TheAMCForum Joined: Jul/03/2007 Location: Minnesota Status: Offline Points: 193 |
Post Options
Thanks(0)
|
Step 1 is correct, except you will need to pull the turn signal switch far enough out to access the push tab or retaining screw. In the early 80's they changed the lock cylinder retainer to a Torx screw instead of the push-in tab. I believe that if the dimmer switch control is in the column, then it will have the Torx screw. We just replace the lock cylinder in the 83 J-10 and it had the turn lever dimmer control and the Torx screw retainer. Tom |
|
1970 AMX 390 4spd
1970 Javelin 390 Auto (Project) 2002 Grand Cherokee Overland Edition 2002 Olds Intrigue (The Other Orphan) Bloomington, MN |
|
Post Reply | Page 12> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |